As an Amazon Affiliate Partner I earn from Qualifying Purchases

Netgear EX7700 Nighthawk X6 AC2200 Setup InstallationNetgear Ex7700 Setup

Using the current WiFi, the Netgear Nighthawk X6 Tri-Band WiFi Mesh Extender Model:  Netgear EX7700 Setup enables efficient whole-home WiFi. The patented FastLane3 Technology together with a dedicated WiFi Connection prevents the expanded WiFi bandwidth from being cut in half. The first phase in setting up a Netgear Nighthawk EX7700 extender is to link it to your existing wireless network. Using one of the two methods mentioned below to complete the task:

To link to WPS, follow these steps: Using the WiFi Protected Configuration (WPS) system to link to your WiFi network safely. You don’t have to type in the network name (SSID) or password.

To reach the NETGEAR implementation assistant, follow these steps: To use the NETGEAR installation assistant, first switch on the extender and then open a web browser on your computer or mobile device.

Netgear Nighthawk X6 Setup | AC200 EX7700

WPS MethodNighthawk X6 AC2200 Setup

For Netgear Nighthawk X6 Setup using WPS:

  • Enable the X6 AC2200 EX7700 extender.
  • Place your WiFi extender near your router.
  • Connect your extender to a power outlet.
  • Wait for the Control LED to illuminate.
  • On the extender, press the WPS switch.
  • If the Connection Status LED is white, your router and extender are connected properly. If the relation is secure, the Link Status LED will turn blue. Shift the extender closer to the router and try again if the Connection Status LED becomes amber or red.

Note: If your router supports the 5 GHz band, the first time you click the WPS button, your extender can attempt to link to the router’s 5 GHz band.

  • Move your extender to a new position about halfway between your router and the place where your router’s WiFi signal is weak.
  • Bring your WiFi-enabled machine or mobile device to a place where the WiFi router coverage is low.
  • Connect the expanded network with your WiFi-enabled machine or mobile device.

Netgear Nighthawk X6 EX7700 Setup Using Netgear Installation Assistant.

 Using the  installation assistant, complete the following steps:

  • Enable the X6 AC2200 EX7700 extender.
  • Place your WiFi extender near your router.
  • Connect your extender to a power source.
  • Wait until the Power LED turns orange.
  • Connect the extender to your router.
  • Go to the mywifiext.net login page using a web server on a computer or mobile device.
  • The NETGEAR installation assistant appears on the computer.
  • Link your extender to your current WiFi network by following the prompts.
  • Place your extender in a new position halfway between your router and the field with a weak WiFi signal.
  • If you’re having difficulty linking, shift the extender closer to your router and try again before the Connection Status LED turns white.
  • Tie the computer systems to the enhanced WiFi network after you’ve met the perfect spot for the extender.

   NOTE: That’s how you set up a Netgear Nighthawk X6 router (EX7700 AC2200).

 Netgear AC2200 Firmware Update 

Does your WiFi extender suddenly start acting strangely? Even after a good Netgear Nighthawk X6 Setup,is it not providing the necessary speed? If this is the case, upgrade the firmware on the extender as soon as possible. Firmware for the Netgear Extender Setup is a series of instructions built into the hardware device. In layman’s terms, extender firmware is a form of an operating system that is programmed to operate on the particular make and model number of the extender. As a result, make sure the extender’s firmware is up to date.

 Here’s how to update the firmware on a Netgear EX7700:

  • To begin, turn on your X6 AC2200 EX7700 WiFi extender.
  • Connect the extender to your router.
  • After that, launch your preferred web browser.
  • In the address bar, type mywifiext.net and click enter.
  • Use the username and password to log in to your extender.
  • To upgrade the firmware, go to the configuration menu and choose Firmware Upgrade.
  • After that, press the Check icon.
  • If there is a new firmware update available, pick yes to upgrade the firmware.
  • Allow some time for the Netgear Nighthawk EX7700 firmware to properly upgrade.

As an Amazon Affiliate Partner I earn from Qualifying Purchases